For Every Airbrush Artist!

Ready to get involved? Register for free and you won't see any google advertising!

Register

crewchief227's Recent Activity


  1. crewchief227

    crewchief227 replied to the thread Dual action trigger pull weight.

    I know this is kinda old, but wanted to chime in on the subject. I too use an CM-SB for my primary (my secondary a CM-C+), and at first...

    Aug 14, 2018 at 3:51 PM
  2. crewchief227

    crewchief227 liked Jimmyfingerz's post in the thread Dual action trigger pull weight.

    For me I found it very fatiguing when I first started so loosened the tension on my iwata hp-c quite a bit. I use the cm-sb which i’ve been...

    Aug 14, 2018 at 3:40 PM
  3. crewchief227

    crewchief227 replied to the thread SilentAir 20A Not Cutting Off At Pressure.

    Awesome you got that resolved. The pic they sent however looks exactly like my 50-24. So it looks as though by getting that PDF you did all...

    Aug 13, 2018 at 7:18 PM
  4. crewchief227

    crewchief227 replied to the thread Curious HP-TH?.

    See that's what I was thinking, but I have never disassembled the trigger, and top of the air valve.

    Aug 13, 2018 at 12:11 AM
  5. crewchief227

    crewchief227 liked DaveG's post in the thread Curious HP-TH?.

    Honestly, if I had to make a guess, I would say that it is for accessing the top of the air valve, perhaps for through drilling during...

    Aug 13, 2018 at 12:09 AM
  6. crewchief227

    crewchief227 replied to the thread Curious HP-TH?.

    Ok so yes this is my first guess too, but doesn't also seem rather large to be just a lube hole? Let me see if I can dig up the box, and...

    Aug 12, 2018 at 7:46 PM
  7. crewchief227

    crewchief227 liked Vladimir's post in the thread Curious HP-TH?.

    Exactly.

    Aug 12, 2018 at 7:39 PM
  8. crewchief227

    crewchief227 posted a new thread.

    Curious HP-TH?

    So I have been wondering since getting it, what is the purpose of this top hole on my TH? I have disassembled it almost completely, I've...

    upload_2018-8-13_7-59-49.png

    Forum: Airbrushes

    Aug 12, 2018 at 6:24 PM
  9. crewchief227

    crewchief227 replied to the thread Why did I not get one sooner.

    He's right. I went not that long ago for over a month without doing a full teardown cleaning, just daily flushing, but it was not healthy...

    Aug 11, 2018 at 4:45 PM
  10. crewchief227

    crewchief227 replied to the thread Why did I not get one sooner.

    I'm gonna make this as an experiment, but take a film roll canister and drill lots of little holes, small parts should be safe

    Aug 11, 2018 at 7:52 AM
  11. crewchief227

    crewchief227 replied to the thread Why did I not get one sooner.

    Ok ok one more question since we're the only two ultrasonic guys. LOL. Do you use hot water from the tap, or does yours heat? I'm just...

    Aug 10, 2018 at 5:09 AM
  12. crewchief227

    crewchief227 liked DaveG's post in the thread Why did I not get one sooner.

    Yeah, I don't know much more about them than you do. I just figured that this one was built a bit better than the first one I purchased - I...

    Aug 10, 2018 at 5:00 AM
  13. crewchief227

    crewchief227 replied to the thread Siphon vs Gravity airbrush.

    I too have an SB & C+V2 microns, and the difference I notice between the side feed and gravity feed is yes you have to prime the sb so to...

    Aug 10, 2018 at 1:42 AM
  14. crewchief227

    crewchief227 replied to the thread Why did I not get one sooner.

    Yeah I would love to probably step up to a nicer one someday if I find myself using this one that much. I did notice on the commercial...

    Aug 9, 2018 at 10:17 PM
  15. crewchief227

    crewchief227 liked DaveG's post in the thread Why did I not get one sooner.

    I purchase a good number of used and vintage brushes. Some, you may think were never cleaned; not a single time. Needles stuck in the...

    Aug 9, 2018 at 10:13 PM